LISTA pentru DIY - La ce cuplu sa strangem suruburile ?

[Roberto 410]

Am gasit lista asta cu cuplurile in Nm pentru diferite suruburi ale masinii. Eu zic ca e foarte utila pentru cei care bibilesc la masina singuri sau vor sa invete.

Pentru cei care nu stiu, toate suruburile din industria auto si nu numai trebuie stranse dupa niste specificatii si se foloseste o asa zisa Cheie Dinamometrica. Din pacate nici eu nu am, pentru componente mai putin importante le putem strange dupa mana, dar pentru unele foarte importante cum ar fi chiulasa ar trebuie o cheie dinamometrica cu care sa stragnem suruburile la cuplul specificat de producator.

Cuplul se masoara in Nm ( Newton\metru ) dar am mai vazut si in alte sisteme.

Cheile Dinamomentrice pot fi de mai multe feluri si sunt pe mai multe plaje de cuplu ( ex 30 - 100Nm, 200 - 300 ) in functie de scopul folosirii lor, etc. Nu ma pricep eu exact dar asta am citit si eu.

De asemenea, motivul general al ruperii sau craparii unor suruburi ( ex prezoane jante, sau dop baie de ulei cum a patit unul din colegii de forum este strangerea la refuz, fara simt\experienta si fara o cheie dinamometrica ).

Stie cineva unde gasesc o asemenea cheie, pentru amatori, nu vreau una profi ca e cateva sute de lei ci una amatoriceasca ?

Deci lista e in engleza, dar o sa o traduc candva.

Acest topic poate fi facut sticky eventual.

Structura listei este astfel :

Filet\Tip surub\Locatie

Cuplu in Nm

M5

5

M6

10

M7

17

M8

24

M10

50

M12

80

M14

130

Exhaust system

(to the turbocharger (TC))

30 Nm

Cylinder head

Tighten the screws in sequence from the center and outwards.

Stage 1 20 Nm

Stage 2 60 Nm

Stage 3 angle-tighten 130°

Manifold

(cylinder head side)

25 Nm

Pipe screw

(coolant pipe I turbocharger (TC))

26 Nm

Pipe screw

(water heated crankcase ventilation.)

26 Nm

Pipe screw

(oil pressure line I engine block)

38 Nm

Sub-frame nut (lower torque rod)

65 Nm. Angle-tighten 600

Sub-frame screw

105 Nm. Angle-tighten 120°

Intake manifold

19 Nm

Catalytic converter

(to the turbocharger (TC))

(to the exhaust system)

25 Nm

24 Nm

Knock sensor (KS)

20 Nm

Piston cooling valve

(piston cooling oil duct, in cylinder block)

36 Nm

Timing gear pulley

(camshafts without variable valve timing)

20 Nm

Timing gear pulley

(camshafts with variable valve timing)

10 Nm

Heated oxygen sensor (H025)

45 Nm

Carrier plate

Stage 1 45 Nm

Stage 2 angle-tighten 50°

Intermediate section

Tighten the screws in sequence from the center and outwards.

Stage 1 M10 20 Nm

Stage 2 M10 45 Nm

Stage 3 M8 24 Nm

Stage4M7 l7Nm

Stage 5 M10 angle-tighten 90°

Torque converter

50 Nm

Engine mounting Right side

(M10x35 to cylinder block)

Engine mounting Right side

(M8x23 to cylinder block)

Stage 1 35 Nm

Stage 2 angle-tighten 60°

Stage 1 20 Nm

Stage 2 angle-tighten 60°

Lower torque rod, transmission screw

35 Nm. Angle-tighten 40°

Lower torque rod, sub-frame nut

65 Nm. Angle-tighten 60°

Oil filter

(environmental filter)

25 Nm

Oiltrap

l5Nm

Oil pan plug

38 Nm

Oil pump

(countersunk Allen, M6x20, holds the pump housing together)

6 Nm

Oil return line

(turbocharger (TC))

12 Nm

Oil pressure switch

27 Nm

Stud

(at exhaust port, manifold, turbocharger (TC))

20Nm

Plug

(check hole for gauging valve clearance)

20Nm

Plug

(gauge hole I crankshaft seal)

38Nm

Belt tensioner (mechanical)

20 Nm

Flywheel

Stage 1 45 Nm

Stage 2 angle-tighten 65°

Vibration damper -2002 (flanged screws x4)

Stage 1 25 Nm

Stage 2 angle-tighten 30°

Vibration damper 2002- /flanged screws x4

Stage 1 25 Nm

Stage 2 angle-tighten 60°

(center nut)

180 Nm

Temperature sensor (coo Ia nt)

22 Nm

Timing cover,(front/rear)

12 Nm

Timing cover,(upper)

8 Nm

Turbocharger (TC)

(to manifold, without gasket)

25 Nm

Turbocharger (TC)

(to manifold, with gasket)

37 Nm

Spark plugs

30 Nm

Connecting rod cap (connecting rod with treated toothed surface between the connecting rod and cap, screw with waist)

Stage 1 20 Nm

Stage 2 angle-tighten 90°

Connecting rod cap (connecting rod with fracture surface between the connecting rod and cap, fully threaded screw)

Stage 1 30 Nm

Stage 2 angle-tighten 90°

Transmission screw (lower torque rod)

35 Nm. Angle-tighten 40°

Variable valve timing center screw

120 Nm

Variable valve timing center plug

35 Nm

Ball joint - Spring strut, steel: 50Nm +- 12, 37 lb-ft 37 +- 9

Ball joint - Spring strut, aluminum: 40Nm =- 10, 30lb-ft +-9

Control Arm - Subframe L/R:

Stage 1 - 65Mn, 48 lb-ft.

Stage 2 - Angle Tightening 120degrees

Control Arm - Subframe:

Stage 1 - 105Nm, 78 lb-ft

Stage 2 - Angle Tightening90degrees

Front anti-roll bar to Subframe: 50Nm +- 12, 37lb-ft +-9

Rear anti-roll bar to Subframe: 80Nm +-20, 59lb-ft +-15

Lug Bolt Torque: 140Nm - 103 ft.-lb.

Strut brace

Brace to mount(one bolt) -- 58 ftlb 80NM

Mount to body(two bolts) -- 36ftlb 50Nm

Sursa ( ca sa nu fiu nesimtit pentru ca cineva a muncit sa adune lista asta ) - SwedSpeed.com

[Matrixxx 1,425]

wow...Interesant de stiut.

[Midnight Caller 3,187]

    TOATE cuplurile sunt specificate in VADIS la proceduri de service. Nu e o regula sa strangi surubul M5 la 5Nm, pt. ca daca-l strangi in aluminiu iti trebuie un cuplu mai mic, daca il strangi in otzel e cu totul altceva. Conteaza mai mult IN CE infiletezi si pasul surubului decat CE SURUB infiletezi in el. Asta unu la mana

    Doi la mana, alege-ti de AICI : www.toptul.com o cheie dinamometrica dupa bunul plac, si in 2 zile ti-o aduc.

[Matrixxx 1,425]

Spune-mi si mie - unde sa caut pe site (cum se numeste) cheie dinamometrica  \

[Victor 18]

Si eu mi-am cam prins urechile in acel site. Mi-a atras atentia insa o trusa de scule. Fara pret.

Midnight, HELP!

[Midnight Caller 3,187]

Pai sa vedem... Pentru Matrixxx : Le gasesti la "Specialty Wrench"

[attach=1]

Si pentru trusa de scule... care din ele, ca "e mai multe"... Da-mi un cod !

[Roberto 410]

Torque Wrench se numeste in engleza.

Una potrivita pentru majoritatea surubaraielor la masina ar fi cea cu plaja intre 19 - 110 Nm care are acolo codul ANAF1211

Deci cat face una ?

[Midnight Caller 3,187]

Momentan singura livrabila este ANAF1621 - 270RON, TVA inclus, vine a doua zi.

[Victor 18]

30PCS Home Repairs & Maintenance Tool Set

Multumesc

[Midnight Caller 3,187]

Mda... am primit raspuns de la importator... se aduce in 6 luni